When does a fire-rated door also need to provide smoke control?

Mark Asscheman ·
Fire-rated door half-open in a concrete corridor blocking dense grey smoke, amber emergency lighting contrasting cool grey tones on opposite sides.

A fire-rated door needs to provide smoke control when the fire compartment boundary it closes must also prevent smoke migration between zones. Fire resistance and smoke control are separate performance criteria, tested under different standards and classified independently. The sections below unpack when both are required, what the classifications mean, and how architects specify a door that satisfies both.

What is the difference between fire resistance and smoke control in a door?

Fire resistance and smoke control are distinct, independently tested properties of a door. Fire resistance describes how long a closed door maintains its integrity, limits radiant heat transfer, or restricts temperature rise on the unexposed side. Smoke control describes whether the door limits the passage of cold or warm smoke through the closed assembly. A door can hold a fire resistance classification without any smoke control classification, and vice versa.

The two properties follow separate testing routes. Fire resistance is tested under EN 1634-1 and classified under EN 13501-2, producing classifications such as EW60, EI1 60, or EI2 120. Smoke control is tested under EN 1634-3 and classified under the same EN 13501-2 framework, but using smoke-specific designations. Extended application rules for both fire and smoke results are covered by the EN 15269 series.

The practical consequence for architects is that a fire door specification must address both criteria separately. A door that carries an EI2-60 classification has been tested and classified for fire resistance. Whether it also carries a smoke classification depends on whether it was tested under EN 1634-3 and certified accordingly. These are not interchangeable, and a manufacturer’s CE documentation will show them as separate declared performance characteristics.

For industrial fire doors, CE marking is relevant under two standards simultaneously: EN 16034, which covers the fire-resisting and smoke-control closing function, and EN 13241, which applies to industrial doors generally. These two standards address different aspects and both may apply to the same product. They are not alternatives to each other, and a specification should not treat them as such.

Need advice for your project?

Discuss your requirements for fire-rated doors, burglar-resistant roller shutters or a suitable solution with Metacon-Next.

Contact us

When is smoke control required in addition to fire resistance?

Smoke control is required in addition to fire resistance when the fire safety design for a building identifies smoke migration as a risk that the door must address. This is not a universal requirement. Whether a door opening in a fire compartment boundary needs smoke control depends on the project-specific fire safety calculation, applicable sector regulations, client requirements, and any requirements set by insurers.

In practice, smoke control requirements arise most often in the following situations:

  • Escape routes and stairwells where smoke-free conditions must be maintained for safe evacuation
  • Compartment boundaries adjacent to areas where occupants may be present and unable to evacuate quickly
  • Buildings where sector-specific regulations impose additional requirements beyond the baseline, such as facilities storing hazardous substances
  • Projects where the client or insurer specifies a higher standard than the regulatory minimum

The Dutch regulatory baseline under the BBL (Besluit bouwwerken leefomgeving) sets only minimum requirements. It does not prescribe a universal smoke classification for every door opening. A project may require smoke control because the fire safety engineer’s compartmentalisation calculation identifies a risk, because a sector regulation such as PGS15 imposes it, or because the building owner or insurer requires it. None of these should be conflated with a blanket statutory rule.

For architects working on industrial and logistics projects, the key is to identify at the fire strategy stage which openings require smoke control, then specify accordingly. Requesting this information from the fire safety engineer before the specification is written avoids late-stage substitutions that can compromise both performance and documentation.

What do the smoke classifications Sa and S200 actually mean?

Under EN 13501-2, smoke control performance for doors is classified using two designations: Sa and S200. Sa indicates that the door controls smoke leakage at ambient temperature, meaning it limits smoke passage when the door and its surroundings have not yet been heated by fire. S200 indicates that the door controls smoke leakage at elevated temperature, specifically at 200°C, which represents conditions closer to an active fire scenario.

The distinction matters in practice because the two classifications address different phases and locations of a fire event:

  • Sa (ambient temperature smoke control): Relevant where the primary concern is preventing cold smoke from migrating through a closed door before the fire reaches the door assembly. This is often the relevant criterion for escape routes and areas remote from the fire source.
  • S200 (200°C smoke control): Relevant where the door may be exposed to elevated temperatures during the fire event and must still limit smoke passage under those conditions. This is a more demanding criterion and is typically required where the door forms part of the fire compartment boundary closest to the fire.

A door can carry both Sa and S200 classifications if it has been tested and certified for both. The classification report from the testing laboratory will confirm which smoke designations apply, under what conditions, and within what dimensional limits. As with fire resistance classifications, the smoke classification applies only within the extended application range confirmed by the test data. If a specified opening exceeds that range, the classification cannot be applied without a separately assessed solution.

Architects should request the full classification report alongside the CE declaration of performance to confirm which smoke designations a product actually holds. A product described as a “smoke door” in marketing materials is not sufficient evidence of tested and classified smoke control performance.

Can a fire door lose its classification if the wrong hardware is fitted?

Yes. A fire door’s classification applies only to the complete assembly as it was tested, including the door leaf, frame, seals, hardware, and any glazing or accessories. Fitting hardware that was not part of the tested configuration, or omitting components that were present during the test, can invalidate the classification. The door may still close, but it no longer carries the certified performance it is specified to deliver.

This is a critical point for architects and contractors alike. The classification report specifies the exact configuration under which the performance was achieved. Any deviation from that configuration, including the type of closer, the locking mechanism, the hinge specification, or the intumescent seal profile, must be assessed against the extended application rules in the EN 15269 series to determine whether the classification is retained.

Common hardware-related risks include:

  • Substituting a door closer with a different model not covered by the test evidence
  • Adding or removing glazing panels after the door has been specified
  • Using seals or gaskets from a different supplier than those tested
  • Fitting access control hardware or electromechanical locks that were not part of the tested assembly

For industrial fire doors in high-traffic environments, the risk is compounded by operational modifications made after installation, such as adding pass-through hatches, replacing worn seals with non-certified alternatives, or retrofitting automation that was not part of the original tested system. Each of these changes should be assessed against the original classification report before implementation.

Metacon-Next provides full technical documentation, including classification reports issued by Efectis, at the specification stage. This allows architects to confirm which hardware configurations are covered by the test evidence and to identify any deviations that would require separate assessment before the door is ordered or installed. Full documentation is available through Metacon-Next’s product range.

Need advice for your project?

Discuss your requirements for fire-rated doors, burglar-resistant roller shutters or a suitable solution with Metacon-Next.

Contact us

How do architects specify a door that meets both fire and smoke requirements?

Specifying a door that meets both fire and smoke requirements starts with identifying both performance criteria from the fire safety design, then finding a product that has been independently tested and classified for each. The specification must reference the fire resistance classification under EN 13501-2, the smoke control classification under EN 13501-2, and the CE marking under EN 16034. For industrial doors, CE marking under EN 13241 also applies and must not be omitted from the specification.

A practical specification workflow for architects involves the following steps:

  1. Confirm the required performance from the fire safety engineer. Identify which openings require fire resistance only, which require smoke control only, and which require both. Do not assume that all openings in a compartment boundary carry the same requirements.
  2. Request the classification report before committing to a product. The classification report confirms which dimensions were tested, which hardware was included, and how far extended application reaches. A product that cannot supply this documentation at the specification stage represents a risk to the permit file.
  3. Verify the extended application range against the specified opening dimensions. If the opening exceeds the EXAP range, a separately tested or assessed solution is required. This cannot be resolved by assuming the classification applies to all sizes.
  4. Confirm that both fire and smoke classifications are covered by the same tested assembly. A door tested for fire resistance under EN 1634-1 is not automatically tested for smoke control under EN 1634-3. Both must appear in the documentation.
  5. Specify the hardware configuration in full. Reference the hardware as tested and documented in the classification report. Any deviation must be assessed before the specification is finalised.

For industrial applications, the specification challenge is compounded by large opening dimensions, high-cycle operational requirements, and the need to integrate fire and smoke performance with access control, automation, and emergency release systems. These requirements rarely align with standard door catalogues, which is why custom manufacturing backed by in-house R&D and full Efectis-tested documentation is relevant at the specification stage.

Metacon-Next manufactures CE-certified fire-rated industrial doors tested by Efectis, with classification reports, declarations of performance, and EPDs available before commitment to a product. This allows architects to close a specification file with confidence rather than chasing documentation after the order is placed. The product range covers roller curtains, roller doors, overhead doors, sliding doors, and pedestrian doors, with fire resistance classifications ranging from EW60 to EW240 and insulation classifications including EI1 and EI2 variants across multiple durations.

For openings where both fire resistance and smoke control are required, the specification must treat each criterion as a separate, documented performance characteristic. The CE declaration of performance will list both where they apply. Where a product does not carry a smoke classification, it cannot be specified to fulfil a smoke control requirement, regardless of its fire resistance rating.

Architects who are uncertain about which classification a specific opening requires should consult the project’s fire safety engineer or contact Metacon-Next directly for technical guidance. The required classification depends on the project’s fire safety calculation, not on a general rule about building type or door location. For projects where both fire resistance and smoke control are part of the specification, requesting a quotation with the full performance requirements stated upfront ensures that the documentation package matches the specification from the outset.

Related Articles